machine cut
ppf kit

Choose The Right Package For You

Protection packages

Partial bonnet, guards, mirror & bumper

From $1450

All painted panels, mirrors & bumpers

From $4000

Luggage Kit

From $125

Door cup

$20 per door

Full bonnet, guards, mirror & bumper

From $2600

Rocker Kit

$600

Headlight Kit

From $160

ask us about
xpel interior film

Interior vehicle surfaces are exposed to wear & tear just like your vehicle's exterior surfaces. In fact, sometimes the interior is worn even harder than the exterior! XPEL INTERIOR PROTECTION restores, renews, and protects the most trafficked areas in your vehicle like the gloss piano black trim, carbon accents, and anything that's getting scratched between trips.

More details

All You Need To Know about Xpel PPF

frequently asked questions

While you can wax the film, be sure the product you are using doesn’t contain Naphtha or Kerosene in concentrations over 5%, and also avoid waxes that contain dyes. For best results, we recommend using our XPEL Flawless Finish Paint Protection Film Sealant. This product has been specially formulated for use with polyurethane paint protection films to provide the maximum protection and gloss, while containing no ingredients that would cause discoloration over time.

Yes. Paint protection film can be applied to any smooth painted surface.

Our ULTIMATE PLUS PLUS and STEALTH films are warrantied for 10 years. This warranty covers: yellowing, staining, delaminating, cracking, peeling, bubbling, and more. 

Yes. The process is the same as with regular paint: wet the surface with a lubricant such as soapy water and then gently rub the surface with the clay bar. For stubborn insect, bird dropping, or hard water stains, use Simple Green as the lubricant for the detailing clay.

Yes. Any smooth painted surface can be covered with paint protection film.

Acry-solvent, or any other Xylene based solvent, will not harm the film unless left sitting saturated in it for an extended period of time. To use this type of solvent on the film (for removing stains, etc.) wet a microfiber towel with the product and wipe the film for one or two minutes. If the stain remains, allow the solvent to evaporate and then repeat the process.

Yes. XPEL can be installed on marine boats and water craft

Other than the simplest body panels, application of paint protection film is a process which requires a good deal of experience and training to obtain satisfactory results. The compound curves present on most surfaces require the film to be stretched and compressed in a very controlled way to ensure proper adhesion without distorting the adhesive. As such, it is highly recommended that the film is professionally installed.

Yes. XPEL film can be applied over a vinyl wrap or graphics. However, if there are any hard edges that film must cross (as in the case of stripes), it could result in some air being trapped along that edge.

Yes. XPEL ULTIMATE PLUS can be applied to any smooth surface, though care should be taken around any electronics and/or switches so that installation fluids aren’t allowed to get into sensitive areas.

While the edge of the film can be seen from certain angles, people generally do not notice it unless they are looking for it. However, if the car is dirty and dust and dirt is allowed to collect along the edge of the film, it will be more noticeable. Once the car is cleaned, it will be once again difficult to detect unless looking for it.

No special maintenance is required for XPEL ULTIMATE PLUS. However, the film will last longer and will be easier to clean if treated twice a year with XPEL Flawless Finish Paint Protection Film Sealant.

Any of our films can be installed on Chrome, though the finish will look slightly different than if left unprotected. We recommend having your installer apply a small swatch to the desired surface so you can see what it looks like before deciding.

XPEL ULTIMATE PLUS is warrantied for 10 years against a range of issues including yellowing.

The clear coat is the self-healing layer and is approximately 13 microns thick. If that layer is penetrated, the film will not heal.

Yes. But wait 48 hours after installation to allow the film to dry completely.

XPEL ULTIMATE PLUS is 8.5 mils (.0085 inches) thick.

Yes, pressure washers can be used on XPEL paint protection films, provided the film has completely dried after installation (typically 48 hours) and provided the high-pressure water is not pointed directly at the edges of the film.

It is highly unlikely for paint protection film to harm OEM paint. Paint systems used on modern assembly lines today produce a minimum bond strength of 16 MPa and maximum of 25 MPa between the panel and the paint depending on color, iridescence and the system used. Our film’s bond to the painted surface at normal state (immediately following installation) is .0753 MPa. Even after years of heat and sun, the bond between the film and the paint increases to only 0.17 MPa. What that means is in the absolute worst case scenario, the bond of factory paint to the panel is over 94 times stronger than the bond of our film to the paint. In the best case, the paint is 332 times stronger.
That being said, it is still recommended to have a professional remove the film in accordance with our published guidelines.

Yes. XPEL can be installed on your cars headlamps and fog lamps

You may use any standard car wash soap, rinse free car wash, or detail spray to clean the film, provided that the product does not contain more than 5% naphtha or kerosene.

The self-healing clear coat of our ULTIMATE PLUS and STEALTH films is designed to repair itself from swirl marks and light scratches from car washes, etc. If a piece of debris has penetrated all the way through the clear coat on the film, it will not self-heal. The only way to fix this would be to have the piece of film replaced.